-
China Factory for Flexible Joint Tozen - A-9 ~Other Products – Lide
Details Clamp Rubber Expansion Joint Clamp-Pipe-Connector Flange Gasket-1 Triple Arch Expansion Joint Rubber Joint Tee SA-Reducer Flange Gasket-3 Flange Gasket-2 -
2018 New Style Evr Flexible Joint - A-4 ~Spool Type Rubber Expansion Joint – Lide
Details The spool type rubber joint is molded type, with a metal collar reinforced at the neck of the body. The ST stype uses a light reaining ring to support the integral flange. STF is filled arch, with 50% of the ST allowed movements, but it has 4 times spring rates than hollow arch. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pressure 1.5Mpa 2.4Mpa 3.75Mpa Burst Pressure Mpa (Kgf/Cm2) 3 (30) 4.8 (48) 5.5 (55) Vacuum Kpa (Kgf/Cm2) ... -
Factory Price For Stenflex Non-Metallic Joint - A-9 ~Other Products – Lide
Details Clamp Rubber Expansion Joint Clamp-Pipe-Connector Flange Gasket-1 Triple Arch Expansion Joint Rubber Joint Tee SA-Reducer Flange Gasket-3 Flange Gasket-2 -
Wholesale Discount Malaysia Rubber Bellow Distributor - A-9 ~Other Products – Lide
Details Clamp Rubber Expansion Joint Clamp-Pipe-Connector Flange Gasket-1 Triple Arch Expansion Joint Rubber Joint Tee SA-Reducer Flange Gasket-3 Flange Gasket-2 -
Factory For Single Sphere Flexible Hypalon Rubber Expansion Joints - A-7 ~Rubber Pipe Connector – Lide
Details Rubber Pipe is an economical, abrasion-resistant replacement for steel and cast iron pipe, either in straight lengths or where a specified radius is required. B-1 Rubber Pipe may be used in conveying ore, corrosive chemicals, sand,and other abrasive slurries. It is absolutely necessary that rigid metal pipe on both ends of the pipe be properly anchored to eliminate the danger of excessive elongation. If the pipeline is not anchored, control units should be used. Material: EPDM, NBR,NR... -
Online Exporter Triple Arch Expansion Rubber Joint - A-3 ~Wide Arch Rubber Expansion Joint – Lide
Details Wide arch system is the molded expansion joint, with integral flange and without a metal reinforcement at the neck of the body. Wide arch allows greater movements and low spring rates comparing to spool type. WA and WAF is used for an economical wide arch rubber expansion joint. WAF is filled arch, with 50% of the WA allowed movements, but it has 4 times spring rates than wide arch. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pre... -
Factory directly Wras Approved Rubber Manufacturer - A-8 ~Standard Flanges – Lide
Details The elastomers are assembled with the mating flanges, with different standards and different pressures. Sometimes, buyers need us to buy for them, shipped together with rubber joints. Below is the flange standards which we can supply: 1) ANSI B16.5, ASME B16.47 FLANGE Design: welding neck, slip on, blind, socket welding, threaded, lap-joint Pressure: 150#, 300#, 600#,900#,1500#, Wall thickness for welding neck flange: STD, SCH40, SCH80, SCH160. SCHXXS Material: carbon steel... -
Hot sale Factory Moulded Rubber Bellows - A-2 ~Double Arch Rubber Expansion Joint – Lide
Details Double-arch products are used where more movement is needed. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pressure 1.5Mpa 2.4Mpa 3.75Mpa Burst Pr... -
2018 Good Quality 4 Expansion Joint - A-6 ~Control Units – Lide
Details A control unit assembly is a system of two or more control rods placed across an expansion joint from flange to flange to minimize possible damage to the expansion joint caused by excessive motion of the pipeline. The control rod assemblies are set at the maximum allowable expansion and/or contraction of the joint and will absorb the static pressure thrust developed at the expansion joint. When used in this manner, they are an additional safety factor, minimizing possible failure of t... -
Wholesale Price China 4 Inch Rubber Coupling - A-4 ~Spool Type Rubber Expansion Joint – Lide
Details The spool type rubber joint is molded type, with a metal collar reinforced at the neck of the body. The ST stype uses a light reaining ring to support the integral flange. STF is filled arch, with 50% of the ST allowed movements, but it has 4 times spring rates than hollow arch. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pressure 1.5Mpa 2.4Mpa 3.75Mpa Burst Pressure Mpa (Kgf/Cm2) 3 (30) 4.8 (48) 5.5 (55) Vacuum Kpa (Kgf/Cm2) ... -
Ordinary Discount Industrial Rubber Joint Distributor - A-6 ~Control Units – Lide
Details A control unit assembly is a system of two or more control rods placed across an expansion joint from flange to flange to minimize possible damage to the expansion joint caused by excessive motion of the pipeline. The control rod assemblies are set at the maximum allowable expansion and/or contraction of the joint and will absorb the static pressure thrust developed at the expansion joint. When used in this manner, they are an additional safety factor, minimizing possible failure of t... -
Wholesale Discount Germany Made Rubber Expansion Joint - A-8 ~Standard Flanges – Lide
Details The elastomers are assembled with the mating flanges, with different standards and different pressures. Sometimes, buyers need us to buy for them, shipped together with rubber joints. Below is the flange standards which we can supply: 1) ANSI B16.5, ASME B16.47 FLANGE Design: welding neck, slip on, blind, socket welding, threaded, lap-joint Pressure: 150#, 300#, 600#,900#,1500#, Wall thickness for welding neck flange: STD, SCH40, SCH80, SCH160. SCHXXS Material: carbon steel...
-
Phone
-
E-mail
-
Whatsapp
whatsapp
-
WeChat
Jessy Lin
-
WeChat
Ellen Zhang
