-
Reliable Supplier India Made Rubber Expansion Joint - A-6 ~Control Units – Lide
Details A control unit assembly is a system of two or more control rods placed across an expansion joint from flange to flange to minimize possible damage to the expansion joint caused by excessive motion of the pipeline. The control rod assemblies are set at the maximum allowable expansion and/or contraction of the joint and will absorb the static pressure thrust developed at the expansion joint. When used in this manner, they are an additional safety factor, minimizing possible failure of t... -
factory customized Molded Rubber Expansion Joint - A-2 ~Double Arch Rubber Expansion Joint – Lide
Details Double-arch products are used where more movement is needed. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pressure 1.5Mpa 2.4Mpa 3.75Mpa Burst Pr... -
Best quality Proco Rubber Expansion Joints - A-6 ~Control Units – Lide
Details A control unit assembly is a system of two or more control rods placed across an expansion joint from flange to flange to minimize possible damage to the expansion joint caused by excessive motion of the pipeline. The control rod assemblies are set at the maximum allowable expansion and/or contraction of the joint and will absorb the static pressure thrust developed at the expansion joint. When used in this manner, they are an additional safety factor, minimizing possible failure of t... -
Super Lowest Price Ansi 150# Rubber Expansion Joints - A-7 ~Rubber Pipe Connector – Lide
Details Rubber Pipe is an economical, abrasion-resistant replacement for steel and cast iron pipe, either in straight lengths or where a specified radius is required. B-1 Rubber Pipe may be used in conveying ore, corrosive chemicals, sand,and other abrasive slurries. It is absolutely necessary that rigid metal pipe on both ends of the pipe be properly anchored to eliminate the danger of excessive elongation. If the pipeline is not anchored, control units should be used. Material: EPDM, NBR,NR... -
Factory Cheap Hot Oil Resistant Rubber Bellow Supplier - A-5 ~Threaded Union – Lide
Details Threaded unions is used When an economical threaded pipe connection is needed, the surface of the union is available both hot-dip galvanizing and electroplating. Both ends provided with a malleable iron union with female thread BS or ANSI. Specifications II Working Pressure Mpa (Kgf/Cm2) 1.6 (16) Test Pressure 2.4Mpa Burst Pressure Mpa (Kgf/Cm2) 4.8 (48) Vacuum Kpa (Kgf/Cm2) 86(660) Materials EPDM/NBR/SBR/NR Diameter Range DN15-DN80 Connection Method THREAD Flan... -
Quality Inspection for High Pressure Rubber Joint - A-3 ~Wide Arch Rubber Expansion Joint – Lide
Details Wide arch system is the molded expansion joint, with integral flange and without a metal reinforcement at the neck of the body. Wide arch allows greater movements and low spring rates comparing to spool type. WA and WAF is used for an economical wide arch rubber expansion joint. WAF is filled arch, with 50% of the WA allowed movements, but it has 4 times spring rates than wide arch. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pre... -
Cheapest Factory Moulded Rubber Bellows - A-1 ~Single Arch Rubber Expansion Joint – Lide
Details The single-arch product can reduce the vibration and noise, which can also solve the axial/lateral/angular movements/eccentric problems. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Specifications I II III Working Pressure Mpa (Kgf/Cm2) ... -
2018 New Style Single Sphere Rubber Expansion Joint - A-3 ~Wide Arch Rubber Expansion Joint – Lide
Details Wide arch system is the molded expansion joint, with integral flange and without a metal reinforcement at the neck of the body. Wide arch allows greater movements and low spring rates comparing to spool type. WA and WAF is used for an economical wide arch rubber expansion joint. WAF is filled arch, with 50% of the WA allowed movements, but it has 4 times spring rates than wide arch. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pre... -
Factory wholesale Dilatoflex Rubber Expansion Joint - A-1 ~Single Arch Rubber Expansion Joint – Lide
Details The single-arch product can reduce the vibration and noise, which can also solve the axial/lateral/angular movements/eccentric problems. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Specifications I II III Working Pressure Mpa (Kgf/Cm2) ... -
Factory Free sample Double Expansion Joint - A-5 ~Threaded Union – Lide
Details Threaded unions is used When an economical threaded pipe connection is needed, the surface of the union is available both hot-dip galvanizing and electroplating. Both ends provided with a malleable iron union with female thread BS or ANSI. Specifications II Working Pressure Mpa (Kgf/Cm2) 1.6 (16) Test Pressure 2.4Mpa Burst Pressure Mpa (Kgf/Cm2) 4.8 (48) Vacuum Kpa (Kgf/Cm2) 86(660) Materials EPDM/NBR/SBR/NR Diameter Range DN15-DN80 Connection Method THREAD Flan... -
Factory making Magoca Rubber Expansion Joint - A-7 ~Rubber Pipe Connector – Lide
Details Rubber Pipe is an economical, abrasion-resistant replacement for steel and cast iron pipe, either in straight lengths or where a specified radius is required. B-1 Rubber Pipe may be used in conveying ore, corrosive chemicals, sand,and other abrasive slurries. It is absolutely necessary that rigid metal pipe on both ends of the pipe be properly anchored to eliminate the danger of excessive elongation. If the pipeline is not anchored, control units should be used. Material: EPDM, NBR,NR... -
OEM China Epdm Rubber Gakset - A-1 ~Single Arch Rubber Expansion Joint – Lide
Details The single-arch product can reduce the vibration and noise, which can also solve the axial/lateral/angular movements/eccentric problems. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Specifications I II III Working Pressure Mpa (Kgf/Cm2) ...
-
Phone
-
E-mail
-
Whatsapp
whatsapp
-
WeChat
Jessy Lin
-
WeChat
Ellen Zhang
