-
Popular Design for High Pressure Rubber Bellow Supplier - A-1 ~Single Arch Rubber Expansion Joint – Lide
Our available goods The single-arch product can reduce the vibration and noise, which can also solve the axial/lateral/angular movements/eccentric problems. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Specifications I II III Working Pressu... -
Factory source Double Sphere Rubber Expansion Joint - A-3 ~Wide Arch Rubber Expansion Joint – Lide
Our available goods Wide arch system is the molded expansion joint, with integral flange and without a metal reinforcement at the neck of the body. Wide arch allows greater movements and low spring rates comparing to spool type. WA and WAF is used for an economical wide arch rubber expansion joint. WAF is filled arch, with 50% of the WA allowed movements, but it has 4 times spring rates than wide arch. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16... -
Top Suppliers Rubber Bellow Manufacturer - A-7 ~Rubber Pipe Connector – Lide
Our available goods Rubber Pipe is an economical, abrasion-resistant replacement for steel and cast iron pipe, either in straight lengths or where a specified radius is required. B-1 Rubber Pipe may be used in conveying ore, corrosive chemicals, sand,and other abrasive slurries. It is absolutely necessary that rigid metal pipe on both ends of the pipe be properly anchored to eliminate the danger of excessive elongation. If the pipeline is not anchored, control units should be used. Material: ... -
Factory Cheap 4 Inch Rubber Coupling - A-1 ~Single Arch Rubber Expansion Joint – Lide
Our available goods The single-arch product can reduce the vibration and noise, which can also solve the axial/lateral/angular movements/eccentric problems. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Specifications I II III Working Pressu... -
Factory source Rubber Coupling Joint - A-7 ~Rubber Pipe Connector – Lide
Our available goods Rubber Pipe is an economical, abrasion-resistant replacement for steel and cast iron pipe, either in straight lengths or where a specified radius is required. B-1 Rubber Pipe may be used in conveying ore, corrosive chemicals, sand,and other abrasive slurries. It is absolutely necessary that rigid metal pipe on both ends of the pipe be properly anchored to eliminate the danger of excessive elongation. If the pipeline is not anchored, control units should be used. Material: ... -
Cheap PriceList for Butyl Flexible Rubber Joints - A-5 ~Threaded Union – Lide
Our available goods Threaded unions is used When an economical threaded pipe connection is needed, the surface of the union is available both hot-dip galvanizing and electroplating. Both ends provided with a malleable iron union with female thread BS or ANSI. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pressure 1.5Mpa 2.4Mpa 3.75Mpa Burst Pressure Mpa (Kgf/Cm2) 3 (30) 4.8 (48) 5.5 (55) Vacuum Kpa (Kgf/Cm2)... -
factory customized Open Arch Expansion Joint – A-7 ~Rubber Pipe Connector – Lide
Our available goods Rubber Pipe is an economical, abrasion-resistant replacement for steel and cast iron pipe, either in straight lengths or where a specified radius is required. B-1 Rubber Pipe may be used in conveying ore, corrosive chemicals, sand,and other abrasive slurries. It is absolutely necessary that rigid metal pipe on both ends of the pipe be properly anchored to eliminate the danger of excessive elongation. If the pipeline is not anchored, control units should be used. Material: ... -
2018 New Style Sponge Rubber Expansion Joint - A-9 ~Other Products – Lide
Our available goods Clamp Rubber Expansion Joint Clamp-Pipe-Connector Flange Gasket-1 Triple Arch Expansion Joint Rubber Joint Tee SA-Reducer Flange Gasket-3 Flange Gasket-2 Our production process quality control We treasure process quality control, there is very strict operation specification each process, which can ensure the goods quality: 1. We use electronic weigher to weigh the weight of ingredients, the precision of weight is gram. So there is no surplus compounds elements; ... -
New Arrival China Pipe Rubber Expansion Joint Types - A-4 ~Spool Type Rubber Expansion Joint – Lide
Our available goods The spool type rubber joint is molded type, with a metal collar reinforced at the neck of the body. The ST stype uses a light reaining ring to support the integral flange. STF is filled arch, with 50% of the ST allowed movements, but it has 4 times spring rates than hollow arch. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pressure 1.5Mpa 2.4Mpa 3.75Mpa Burst Pressure Mpa (Kgf/Cm2) 3 (30) 4.8 ... -
Original Factory Movement Absorption Rubber Bellow - A-1 ~Single Arch Rubber Expansion Joint – Lide
Our available goods The single-arch product can reduce the vibration and noise, which can also solve the axial/lateral/angular movements/eccentric problems. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Specifications I II III Working Pressu... -
Newly Arrival Wras Approved Epdm Rubber Gasket - A-6 ~Control Units – Lide
Our available goods A control unit assembly is a system of two or more control rods placed across an expansion joint from flange to flange to minimize possible damage to the expansion joint caused by excessive motion of the pipeline. The control rod assemblies are set at the maximum allowable expansion and/or contraction of the joint and will absorb the static pressure thrust developed at the expansion joint. When used in this manner, they are an additional safety factor, minimizing possible ... -
Ordinary Discount Us Rubber Bellows - A-8 ~Standard Flanges – Lide
Our available goods The elastomers are assembled with the mating flanges, with different standards and different pressures. Sometimes, buyers need us to buy for them, shipped together with rubber joints. Below is the flange standards which we can supply: 1) ANSI B16.5, ASME B16.47 FLANGE Design: welding neck, slip on, blind, socket welding, threaded, lap-joint Pressure: 150#, 300#, 600#,900#,1500#, Wall thickness for welding neck flange: STD, SCH40, SCH80, SCH160. SCHXXS Material: ...
-
Phone
-
E-mail
-
Whatsapp
whatsapp
-
WeChat
Jessy Lin
-
WeChat
Ellen Zhang
